Exhaust Thru Bed Vertical Stack kit 5" Ford,dodge truck

Get the Big Rig Look

every single item is in stock,there is no back order,your order today,we will ship out the next business day.

Kit Only!!!!!!

We have the complete system in our store if you want the stacks with them.This is for the people that have already purchased the stacks or want bigger sizes.

Compatible with any full size pickup truck regardless of brand and only requires 1 hole to be cut in the floor of bed.

**********

Shipping include to lower 48 states

Our kits includes everything you will need to give your truck the Big Rig Look Except the chrome stacks

Included are items below;

1)4" Accusal Alz. Clamp

2)5" Accusal Alz. Clamp

1)5" THru-Bed Y-pipe

1)5" Zinc Flat Bolt Clamp

1)4" 90% Elbow(Short)

1)5" 90% Elbow(Long)

1)Left Stack Mount

1)Right Stack Mount

1)4"X12" Stainless Flex

2)Westfalia 4" Alz. Clamp

If you need the reducer you will need (3" or 3.5")are listed seperately in our store

Shipping included to lower 48 states

Please read our feedback

Everyone has been Extremely happy

We try very hard to get you your items asap and in great shape

We take extra time in packaging our products.

If you need instructions please read below for detailed installation instructions

Installation instructions for vertical stack kit

Note:Before removing the OEM exhaust System, read all of the instructions.

Measure Twice and Cut Once!

1)Remove exhaust from back of cab all the way to the back of truck.

2)Remove the heat shield from the bottom of the be(if equipped).

3)Put long elbow into ID of Y Pipe. Place in bed to determine where the hole will go.A bit of the OD end of the elbow may need to be trimmed to fit the correct width of the bed.

4) Figure where you want your kit located. Confirm your hole location from the underside and topside BEFORE drilling any thing.

5) after the hole is drilled through the bed floor, place Y Pipe through the hole, place stacks into the ID en and right can be swapped for better and easier mounting. These mount to the sides not the front of the bed.

6)Hold the PUB-L and R up to the stack to determine hole locations through the inside lip of the truck bed. The left and the right can be swapped for better and easier mounting.These mount to the sides not the front of the bed.

7) Drill the holes through the bed lip and loosely bolt the brackets to the bed.

8)Slide the Bright Accusal Clamps over the stack and capture the brackets with them.You can flip the clamp either way to hide the bolt area.

9)Slip the short 90 degree elbow into the opening of the Y pipe(underneath). Put the flex assembly over the elbow about 2" to 2 1/2 ".

10)Measure the length from 2 1/2" into the flex forward, to go over your existing pipe that will probably need to be cut.If you have 3" or 3 1/2" diameter,reducers do not come with this kit.

11)At this point, you can measure and figure where the center clamp should go through the floor of the bed. This clamp should bolt the Y pipe to the long left side elbow and to the floor bed.

12)Snug up all the clamps,etc. Make sure nothing is bound, rubbing ,or touching any thing that it shouldn't.

13)Before starting engine,make sure the chrome is Clean: grease and oil free.A good hand or fingerprints will"Bake" into finish if not clean.

14)Tighten everything.Start engine and check for leaks, etc.Take for a test drive

15)************ENJOY!!******************

Please feel free to email us with any questions you might have or visit our store for your additional exhaust needs

Thanks for viewing our listing.Please let your friends know about the

Chromeroom

Store on Ebay!!!!

EBAY ROCKS!!!

This kit has a 4" ID inlet under the cab.you will need a reducer and an additional clamp if your exhaust system is 3" or 3.5" listed separastley in our store.

Every single item is in stock,there is no back order,you order today,we ship out the next business day.